MARBLING FOR BEGINNERS WITH CRAFTY ARTS’ MINI-KITS
CONTAINING BASTION MARBLING PAINT
Marbling is done by floating paints on a thickened liquid solution (called a gel). Once you are happy with the floating design it is frozen in time by laying a piece of paper or fabric onto the surface of the gel and allowing it to float and absorb the pattern. The paper or fabric is lifted up off the gel to reveal a unique once off print. You can also marble odd shaped 3D objects by dipping them gently into the marbling bath allowing the paint to wrap around it e.g.
wooden items and ceramic in bisque state. Only marble porous surfaces that normal acrylic paints will adhere to.
You can marble other surface types by either sanding off finishes or painting on a suitable paint primer first (primers available from hardware stores). Marbling is done using small amounts of paint. To get best absorption and adhesion of paint onto the surface, the item to be marbled should be pre-treated first by dipping it into the fixative solution and allowing it to dry before putting it in the marbling bath.
Step 1: Make the Marbling Bath Gel
Add the little packet of Gel Powder to 1 litre water and mix well
If you don’t have a good mixer, use hot kettle water to assist with dissolving the powder.
The gel should reach the viscosity (flow) of an egg white upon standing. Allow the gel to stand for a few hours before using it (all air that makes it appear white should disappear with time and all lumps will dissolve).
Preserve your marbling gel for longer by storing it in a fridge and keeping a lid on it. It is important to give it a good mix and let it warm to room temperature before marbling again.
Add the gel to the marbling bath or tray that you plan to use (a cat litter tray or foil baking tray works well). For flat surface marbling make the bath at least 3cm deep. For dip marbling you will require a much deeper bath.
Step 2: Pre-treat the surface to be marbled
For paper and non-fabric surfaces – Add the packet of Fixative Powder into 125ml water.
For paper sponge onto paper evenly. Allow to dry and press the paper flat before marbling.
For other surfaces dip the surface to be marbled into the fixative solution, hold it in the solution for a few seconds and then hang it up to dry.
For Fabric – Add half a packet of Fixative Powder into 125ml water or, a whole packet info 250ml water. Soak fabrics for 10min, line dry and then marble. Iron with a cool iron if needed. Note that a higher concentration Fixative Solutions will make fabric brittle and it will tear.
Step 3: Prepare your paints
Fill the paint container with water, up to the line (top of label).
Acrylic paints must be made to flow very readily. Bastion Paint Marbling and Pouring Acrylic should be diluted as follows: Your paint should be the same viscosity as full cream milk.
Step 4: Create your design
Diluted paint is dripped carefully onto the surface of the marbling bath. Apply the colours of your choice in drops at the points that you require them. Each drop will spread out to (a thin film). Different paints and colour drops close together will not mix but tend to push one another into smaller shapes or tighter veins. The colours will intensify more with each layer. Don’t squirt the paint onto the bath as it will sink. Use a mini-rake, toothpick or items of your choice to create your design by gently drawing in the paint which is floating on the surface.
Step 5: Marble your paper, fabric or item
Before you start make sure the surface of the gel in the marbling bath is clean and has no skin. Skim the surface or absorb dirt specs by laying newspaper onto the surface. It is important to have your gel and paints at room temperature before you start.
For 2-D marbling lay paper or fabric onto the surface making sure to not trap bubbles. Tap on the surface to release bubbles if needed. Let paper lie for a minute and then lift the paper. For fabrics allow the fabric to lie on the surface until wet and then lift. Rinse as much of the gel off as possible without rubbing. Line dry out of direct sunlight. For 3-D marbling gently dip objects into the bath watching how the paint pulls towards the objects as they are lowered in. Remove your marbled item and rinse off immediately with gently flowing cold water. Hang it up to dry and you are done.
Step 6: Clean your marbling bath surface for your next design
If enough paint remains in the bath after marbling you can create a second print.
Skim the surface of your gel with strips of newspaper or lay newspaper onto the marbling bath surface to absorb all remaining paint. Paint that sinks to the bottom will not affect your next creation. Use the same marbling bath to create your next work of art. You need only change your marbling bath gel when you can’t get the surface clean, when it starts to smell or when it loses viscosity and becomes so thin that paint sinks. Make sure that the depth is always more than 3cm. If you really want to marble on a large scale we can provide a preservative to significantly prolong the life of your bath.
BASTION MARBLING PAINT IS ALSO AVAILABLE AT CRAFTY ARTS IN 100ML